Step 2.Contect the four connection device of the seat to the D-rings on both side of the paddle board.
Note:You can put your carry-on items such as shoes in the bag that comes with the seat.
Step 1. Please take the hand pump and pump tube out of the accessories bag, then connect them and tighten them clockwise.
Step 2. Open the cap of the air valve anticlockwise(please kindly noted not the whole air valve); Check the white spring button in the middle of the air valve, if it pops up, it is inflated; Otherwise, it is deflated. Press the button to make sure it pops up.
Step 3. Firstly, connect the pump tube to the air valve and fasten it clockwise. Start to inflate, the barometer needle will not move before 5PSi.We recommend inflating until 10-15 psi, which will take about 10 minutes.
Step 4. Unscrew the pump tube anticlockwise and fasten the cap of the air valve clockwise.
Step 1. Take the 3 pieces of the paddle out of the accessories bag and then connect them.
Step 2. Adjust the tightness by rotating the screw adjuster, clockwise for tightening, and anticlockwise for loosening.
Step 3. Adjust the upper and lower telescopic paddle handle to its proper position, and buckle the screw regulator. If it is still loose, tighten the regulator clockwise.
]]>
Step1. Take the ankle leash out of the accessories bag and connect it to the D ring on the board tail.
Step2. Then fasten it on the ankle.
Step 2. Hang the carry strap on one shoulder.
Read More:
]]>Step 2. Insert the slot, and fasten the fixing pin.
Read More:
]]>Step 2. Fix it at the D-ring position on either side of the supboard.
Step 3. Fix the paddle with the paddle hold device to prevent the paddle from sliding into the water.
Step 1. Special GoPro fixing foundations can be purchased from the Supzoom website.
Step 2. Fix the foundation with the 3M adhesive tape and then Secure the GoPro to the foundation connection.
Step 1. Special fishing rob holder can be purchased from the Supzoom website.
Step 2. Fix the foundation with the 3M adhesive tape.
Step 1. Open the turnbuckle and tighten it clockwise.
Step 2. Adjust the height properly again and then lock the turnbuckle.
Step 2. Take the hand pump and pump tube out of the accessories bag and then Connect the tube to the interface of the hand pump base, then tighten clockwise.
Step 3. Open the extraction valve and use the pump to extract air until the air in the paddleboard is evacuated.
Step 2. Fix the wrench at the correct position of the air valve and fasten the air valve clockwise.
Step 3. Check the white spring button in the middle of the air valve, if it pops up, it is inflated; otherwise, it is deflated. Press the button to make sure it pops up. Connect the pump tube to the air valve, and fasten it clockwise. Next, Connect the pump tube to the air valve and fasten it clockwise. Finally, inflate the sup board to 10PSI.
Step 4. Use the foam water to check again and see if there is air leakage. If there are no obvious bubbles, it has been repaired.
Read More:
]]>Step 1. First, you need to deflate the inflatable paddle. Next, Remove the repair kit from the accessories kit and then remove the wrench.
Step 2. Fix the wrench at the correct position of the air valve, and loosen the air valve anticlockwise. Take the air valve out, please kindly noted the air valve foundation is not needed to take out.
Step 3. Align the air valve foundation with the air valve port and clear the fibers of the drop stitch fabric covering the foundation. Finally, fix the new air valve on the foundation, then fix the wrench on the air valve position and tighten it clockwise.
Step 2. Press the air valve spring button continuously to check whether the bottom of the air valve cannot be reset. If it can't be reset, it can be determined it is caused by the deviation of the position of the air valve core.
Step 3. Clamp-on the core base with a suitable clip and clamp the core base back to its original position. Press the air valve spring button again to check whether the bottom of the air valve core is reset. If it has been reset, it has been repaired.
Step 4. Check the white spring button in the middle of the air valve. if it pops up, it is inflated; Otherwise, it is deflated. Press the button to make sure it pops up. Connect the pump tube to the air valve, and fasten it clockwise.
Step 5. Inflate the sup board to 10PSI and then use the foam water to check again and see if there is air leakage. If there are no obvious bubbles, it has been repaired.
Step 2. Spray the foam water on the air valve, and continuously observe whether continuous bubbles are emerging.
Step 3. If obvious bubbles are emerging for many times in a row, it can be determined that there is air leakage at this position.
Step 1. Firstly, open the cap of the air valve and press the white spring button to deflate.
Step 2. Wind up the paddleboard from the other end which doesn't have the air valve.
Step 3. Fasten the air valve cap, and pay attention to prevent sand and water from entering the air valve. Finally, Put the supboard into the Supzoom bag.